Baxi brand boilers are one of the best equipment options used in arranging heating systems. Various configurations of this modern thermal equipment have been developed, respectively, rather comfortable operating conditions are provided to potential users.
However, like any other electronic-mechanical devices, this type of technology is not completely immune from malfunctions. Technical documentation mentions possible failures of various types at least 99 times.
How are malfunctions expressed, what numbers are accompanied by errors of the Baksi boiler, and how can the problem be eliminated at home? Consider this issue in our article.
Documented codes and their decryption
Modern household appliances are notable for the fact that microcontrollers are actively used in its design. The use of these electronic elements allows you to control the equipment efficiently and rationally without involving a person.
The controllers also make the monitoring function effective, organize the timely detection of failures and accurately diagnose malfunctions.
All this applies to thermal equipment - domestic gas boilers. The electronic control system is able to detect malfunctions of a Baxi domestic boiler and inform the user (mechanic) of alleged errors in the operation of the equipment.
Judging by the technical documentation, it is possible to detect almost any system error with the display of a specific number.
This kind of error coding in Baxi equipment is shown on the system display when an individual component malfunctions during operation or a malfunction occurs for other reasons.
Further, using the error number issued by the system, the owner of the equipment or a invited mechanic will be able to quickly determine the place of failure and eliminate the emergency.
All existing error codes for Baxi domestic boilers are presented in a list with at least a hundred options. To clearly describe each of them, one article is clearly not enough. Therefore, we consider the main ones - often found in practice.
Code E01 and E04 - flame monitoring sensor
The situation, typical for most models, is connected with the functionality of locking the boiler ignition system. The classic error code for such cases - “E01” or “01E” (as well as “E04” or “04E”) is displayed on the information display.
If the design does not provide for a display, the same error is identified by the corresponding LED indicator.
Gas flow instabilities, flame sensor malfunctions, and other technical malfunctions of Baxi equipment are the result of code E01 (01E)
Relationship of error and possible situations:
- there is no gas supply;
- broken contact on the flame sensor;
- flame control sensor dirty;
- malfunction of the ignition system;
- phase and zero on the supply line do not match;
- malfunctions of a gas tap, electronics, coaxial chimney.
Accordingly, based on possible malfunctions, it is necessary to check all the specified components (elements) in order to verify the correct operation, and in the opposite case, carry out repair measures.
Code E02 - thermostat fuse against overheating
The manifestation of this error, displayed as “E02” or “02E”, may also be accompanied by various variations of the defects.
An example of the appearance of the code 02E (E02) on the display of the boiler model Caldera Baxi Roca Victoria. Meanwhile, similar failures are characteristic of other models.
In particular, the following defects may occur:
- the water temperature of the main circuit has been exceeded;
- circuit temperature sensor defective;
- no contact on the temperature sensor of the heating circuit;
- coolant circulation in the primary heat exchanger circuit is not enough;
- clogged filter, heat exchanger, air in the system;
- defective circulation pump;
- malfunction on the electronics board.
The same errors are typical for boiler models where there is no display. They are determined by the presence of an indicator glow with a temperature marker.
Code E03 - traction sensor
This error is preceded by malfunctions related to the draft sensor, thermostat or pneumatic relay. The error code is displayed as “E03” or “03E”.
The situation is typical both for equipment where a closed combustion chamber is used, and for equipment where an open combustion chamber is used.
Usually (with a higher degree of probability) the fault code E03 (03E) corresponds to defects associated with malfunction of the traction sensor
Fault Options:
- the length of the chimney is large;
- the chimney is narrowed or closed by a foreign object;
- Venturi injector defective;
- There is no connection between electronics and pneumorelays;
- fan malfunction or no contact;
- incorrect connection of the pneumatic relay.
The control of the same error on models equipped with LED indicators is carried out taking into account the markers "asterisk" or "house".
Codes E05-09 - DHW and burner flame control
The group of marked sensors actually performs related operations related to the control of the DHW temperature or the control of the flame of a gas burner.
Errors "E05", "E06" (coolant temperature), "E07", "E08", "E09" (flame and flue gas control) are typical for boilers of the "Main5" and "ECO-5" models, as well as others.
The group of codes 05 - 09 most often indicates the problems that accompany the operation of the components of the DHW line. However, a number of malfunctions at other points of the equipment are not excluded.
Malfunctions can manifest various:
- malfunction of the DHW temperature sensor;
- there is no sensor contact from the electronic board;
- overstatement or underestimation of boundary temperatures;
- malfunction of electronics;
- defective heating circuit sensor;
- flue gas sensor defect;
- open grounding circuit of the electronic board.
Most of the problems noted are eliminated by simply testing the circuits with a meter or by replacing the suspected faulty element with another, working.
In approximately this way (connecting a constant resistor to the connector), the operation of the DHW temperature sensor is checked if the fault code 06E (E06) is displayed on the boiler display
Code E10 - minimum pressure switch
The functional component of the system - the minimum pressure switch - is used in almost all Baxi boiler designs, including EcoFour, Fourtech, Main Four, Navola, etc.
However, for some models this functional component may be referred to as a differential pressure switch micro-switch (TIR).
Most practical cases prove that the display of code 10E (E10) indicates problems with the minimum pressure switch or circulation pump
The error “E10” (“10E”) traditionally appears on the display or is displayed by an LED when:
- too low water pressure KO;
- there is no relay contact with the electronic board;
- defect of the minimum pressure switch;
- non-working TIR;
- jammed TIR stock;
- malfunctioning pump;
- circulation of KO or primary heat exchanger (PT) is disturbed;
- water outlet pipe contamination;
- membrane defect (no pressure drop).
Elimination of the E10 error is carried out by checking all the components marked in the list and eliminating the detected defects. The units are cleaned, individual parts or all units are replaced.
Codes E12 and E13 - DGP malfunction
If the code “E12” (“12E”) or “E13” (“13E”) appears on the boiler display, it clearly indicates malfunctions associated with the operation of the BPH - differential hydraulic pressure switch.
Usually, during the testing process, the signal from the device is not detected or there is a signal, but it does not match the specified characteristic (false signal)
The reasons for the appearance of the marked code may be:
- pump shutdown;
- the presence of air in the DHW system;
- low speed of circulation;
- no contact on the TIR or "stuck" contact;
- membrane damage or clogged filter;
- impulse tube clogging.
Accordingly, to determine the malfunction of a particular element, a technical check should be carried out.
And in order to eliminate the problem, it is necessary to replace the faulty element or carry out preventive restoration work.
Codes E21-22 and E97-99 - electrical and electronics
Both codes - “E21” and “E22” - indicate malfunctions associated with the electronic board. Code “E22” may occur if the supply voltage drops below the reference value (162V).
The same code is displayed if the quality of the energy supplied to the boiler does not meet the declared standards.
For the code “E21”, a characteristic moment is the scatter of the controller parameters and the violation of normal gas combustion. In the absence of experience and relevant knowledge, it is better to entrust the repair of the board to the master.
Errors "E97", "E98", "E99" - all three codes are usually associated with defects in the electronics - the electronic board.
Code "E97" indicates the frequency of the supply voltage that does not comply with the standard. The defects present precisely on the electronic board are indicated by the code “E98”.
About the same signal code "E99". True, an “99E” error can also be caused by a too low gas pressure, as well as a malfunction of the flame sensor
The simplest defect is the loss of electrical contact on the gas valve relay. In other cases, a replacement board is usually required.
Codes E25-27 and E32 - temperature defects
The appearance of any of these codes - “E25”, “E26”, “E27”, “E32” - is usually preceded by temperature changes in the heating circuit that occur at a faster rate than specified by the control system.
For example, if the temperature of the heating circuit (KO) rises by more than 1 degree per second, the code “E25” (“25E”) is displayed on the boiler display. For the code “E26” (“26E”) to appear, it is usually enough to exceed the temperature above the set value by 20 ° C.
Faults or malfunctions marked on the display with code E26 (26E) - reaction to temperature deviations. Due to temperature failures, other codes of the same group may appear.
Reasons traditionally causing such codes:
- circulation pump lock;
- clogged filter;
- air inside the system;
- defect in the temperature sensor;
- malfunctions of electronics;
- incorrect installation of the dhw sensor.
To eliminate it, it is necessary to carry out preventive measures aimed at checking and testing the units of hot water supply and CO. Air in the system is removed by a standard technique used by plumbing practice.
The efficiency of the circulation pump is checked on the electrical and mechanical parts.
Codes E35-36 and E40-43 - flame control and GDC
This set of codes mainly indicates malfunctions of gas burner flame control systems and flue gas control systems. So, the code “E35” (“35E”) indicates a mismatch in the arrival of the flame signal.
The code “E36” (“36E”), as a rule, indicates a malfunction of the NTC sensor. Codes “E40”, “E41” and “E42”, “E43” remind the user of the failure of the GDC test for flue gases and ionization current.
A device (flame control sensor), the malfunction of which or contamination may cause an error under the code E35 (35E) and others from the group to appear on the control display
The appearance of these codes is usually accompanied by:
- moisture in the area of the electronic board;
- residual combustion after closing the burner;
- mismatch in the quality of the supply network;
- defective NTC sensor (flue gas sensor);
- lack of communication between the sensor and electronics;
- defects in electronics;
- lack of gas pressure;
- contamination or malfunction of the flame sensor;
- gas valve malfunction;
- too long chimney.
Some of these defects are available to the user to fix on their own.
However, other points, for example, electronic malfunctions and sensor testing, require the intervention of specialists.
Codes E50 and E62 - NTC sensor and flame control
The automation of the Baksi boilers is adjusted to certain parameters of combustion stability, as well as to a certain temperature range of flue gases.
Error E62 - burner flame monitoring sensor
If either of the two parameters (or both at once) goes beyond the limits of the settings, the automation is triggered, and the code “E62” (“62E”) appears on the control display screen.
Traditional reasons:
- faulty or dirty flame control sensor;
- faulty NTC sensor;
- defects in the electronic board.
Sensors are checked by replacing known-good instances, and electronics are tested by instruments designed for such purposes.
Error E50 - NTC temperature sensor
The manifestation of the “E50” error is typical for ECO-5 and Main 5 boilers. The “E50” code is displayed on the control display, as a rule, because the sensor detects the temperature of the heating of the flue gas above 180 ° C.
Another sensor present in the design of the Baxi boiler, the defect of which leads to the appearance of the E50 (50E) code on the control display
In turn, the rise in temperature above the established limit may be due to:
- low coolant circulation rate;
- clogged filters;
- the appearance of hydraulic resistance in the system;
- low concentration of antifreeze;
- defects in the circulation pump;
- contamination of the system or air.
Also, the DTC “E50” (“50E”) is displayed when the NTC sensor breaks down, due to electronics malfunctions, due to improper gas valve settings.
Accordingly, the elimination is ensured by consistent testing of designated nodes and the production of necessary work.
Code E55 - gas valve malfunctions
Often this code - "E55" - makes itself felt due to incorrect calibration of the gas supply valve.
The gas supply valve of the Baksi domestic boiler is a device that often causes the E55 (55E) code to appear on the control display. A fairly sophisticated mechanism that requires fine tuning
To eliminate the occurrence of an error, a calibration procedure should be carried out. Usually this work is done by a specialist, but if you wish, you can try to calibrate yourself by following the instructions.
The author of the video below parses another possible error that was not included in the list of the current publication. In particular, the video shows the malfunction marked with the code “E00”:
The electronic system for detecting errors in the operation of the Baksi boiler with the subsequent output of the corresponding code to the control screen is a very convenient service for the user.
This is a significant help for mechanics when they have to deal with rather complex malfunctions that require additional testing of equipment before and after repair.
If you have questions about the topic of the article or there is valuable information which you can supplement our material, please leave your comments in the block below.