Proper lighting in the bathroom decorates the interior and creates a pleasant atmosphere. Increasingly, when organizing the lighting of the bathroom, LED devices are used - they are convenient to install, safe and cost-effective.
Before proceeding with the installation of the backlight, it is necessary to learn more about the specifics of electrification of wet rooms, study the rules of electrical safety, draw up a wiring plan, pick up lamps and other elements of the system. All these points are detailed in our article.
In addition, we described the procedure for arranging LED backlighting, outlined the main stages of installation and connection of LED strips.
Electrics and high humidity
A large amount of water, frequent changes in temperature, humidity and hot steam, condensation - all these conditions typical for the bathroom create an increased danger when using electricity within it.
To ensure the safety and proper operation of electrical appliances, in such rooms during installation, electricians use only elements protected from steam and water.
Moisture-proof terminal blocks are perfectly suitable for the bathroom, which are able to tolerate high humidity for a long time, and at the same time they noticeably facilitate installation.
Installation of any junction boxes and components should be carried out strictly outside the bathroom. Inside the bathroom, as far as possible, avoid connecting individual wires.
If for some reason it is still necessary to do the so-called twisting, then each such place should be protected as thoroughly as possible with insulating materials from moisture penetration. Most often, the backlight in the bathroom is organized using low-current systems with a power consumption of 12 V.
When installing the main and additional lighting in the bathroom, it is recommended to use special terminal blocks equipped with additional moisture protection
It is almost impossible to get any dangerous electric shock from such an LED lamp even at high humidity. But this does not mean that security measures can be forgotten. All LED devices should be earthed without fail.
The lighting system must be connected to a residual current device, which is triggered when a current leak occurs and interrupts the power supply to a specific object.
With the help of LED lamps and LED-tape, you can significantly diversify the interior decoration of the bathroom, providing the necessary amount of light in the room
In bathrooms it is recommended to organize a separate power supply line to each object or group of objects. Usually a line is allocated for outlets and separately for lighting devices.
If the bathroom is supposed to use powerful equipment (automatic washing machine, hot tub, electric sauna, etc.), then for each such object a separate power line should be made. And for each such group of electricity consumption it is recommended to install a separate RCD.
Detailed instructions for installing the outlet for the washing machine are presented in this article.
All lighting and electrical appliances located in the bathroom must be connected to the distribution panel via a residual current device (+)
Electricity is supplied to low-current LED systems through a special step-down transformer. This appliance also needs to be installed outside the bathroom, i.e. away from a source of high humidity. Almost all modern LED lamps are equipped with a special ground terminal.
Do not neglect this method of protection. Even weak currents can be transmitted and accumulate on wet surfaces. And thanks to steam and condensation, any surface in the bathroom can become damp: walls, floor, profile structures, ceiling, furniture, appliances, etc.
Each lamp installed in the bathroom should be properly grounded. The absence of such protection can bring a lot of problems to the owner of the premises (+)
An accidental touch can transfer the discharge of accumulated electricity to the human body, which in some cases can not only cause discomfort, but also lead to serious electrical injury.
Design and installation features
All of the above points must be considered before drawing up a design scheme of lighting in the bathroom. Installation of LED devices will be taken into account in such a scheme.
Usually you need to decide on the main and additional lighting, provide switches for them, determine the location of outlets for connecting various household appliances.
To avoid confusion and to correctly connect the ends of the electrical wires to the junction box, it is recommended to use color coding
After that, a wiring plan is drawn up, the location of the junction boxes is determined, etc. From the apartment-wide electrical panel to the junction box of the bathroom, a cable with a cross section of 2.5 square meters is laid. mm It is suitable for lighting, as well as for lighting.
Separately lay a more powerful cable designed for large equipment. It is recommended that different cables be color coded to prevent accidental confusion. After that, lay the wire to the switch.
If all lighting fixtures are turned on with one button, then it will be enough to use a conventional double wire.
But LED lighting in the bathroom is usually turned on separately from the main lighting. In this case, use a triple cable. If for lighting a switch with three keys is used, i.e. for three separate groups of fixtures, you will have to use two double cables. The cross section of such a wire should be 1.5 square meters. mm
After that, the cable is laid from the switch directly to the lighting fixtures. It should be taken into account immediately that it is not recommended to carry out open wiring in bathrooms, so you will have to make strobes. In some cases, cable laying in a special plastic box is allowed.
Groups of auxiliary spotlights can be connected in parallel or in series. In the first case, it will be necessary to bring a separate power line to each lamp, in the second - to connect the lamps in one line one after another.
With a parallel connection, both cable consumption and the amount of work increase significantly. In the second case, everything is much simpler and cheaper.
But serial connection at the same time has a number of disadvantages. For example, if one lamp burns out, the power supply to the entire circuit is interrupted. In addition, there is no way to diversify the LED backlight control system.
With a parallel connection, a burned-out element will not spoil the work of the remaining lamps in any way.
If there is a desire to arrange the possibility of turning on not all lamps at the same time, but only some, for example, every second lamp, then a parallel connection will be needed. This allows you to adjust the degree of illumination of the room.
If desired, the methods of connecting the fixtures can be combined, for example, the illumination of the mirror can be performed in a sequential way, and to decorate the bath or ceiling, use parallel connection, etc.
For this type of lighting, it is recommended to take a flexible stranded wire. A monolithic cable can impede the proper installation of fixtures by changing their position. Installation work with a flexible wire is usually not difficult to perform, but all twists should be carefully soldered and insulated.
The stranded wire of the ШВВП type has conductors twisted from a copper wire, sheathed with a PVC plastic coating, which protects the structure from the influence of extraneous factors
Usually, it is recommended to use wires of the ШВВП, ПВС or similar types for fixtures in the bathroom, in which the multi-wire cores are reliably covered with a layer of PVC compound.
Such protection will prevent the spread of fire in case of fire, prevent the formation of fungi, resistant to moisture.
Conclusion of wires through the mounting hole in the wall and connecting them to the two-gang switch
The lead-in cable is necessarily laid in a protective corrugated channel. For systems with ground terminals, a four-wire cable is used, if such an element is missing, a three-core design will be sufficient. Under the spotlights in the canvas of the suspended ceiling, holes of a suitable size are made.
Outlets of the wire should be derived from them, two segments for each switch button, as well as two more wires for the reverse connection. To facilitate installation, it is recommended that the length of the outlets be approximately 15-20 cm. The ends of the outlets of the same color must be smoothed out and twisted together.
At least two wire outlets with a length of about 20 cm should go into the mounting hole for installing a spotlight
If you plan to connect to a switch with two keys, then three twists will come out of each hole. One of them will be common to all luminaires, and the other two for switch keys.
Accordingly, the first twist is attached to each lamp, and the rest - only to those elements that will be controlled by a specific key.
One common wire must be connected to each lamp and output to “zero” (blue wire), the rest are connected to different lamps and connected to the “phase” of different switch keys. 1 and 2 are groups of fixtures
The common wire in the junction box will be connected to the neutral wire, and the phase should be brought to the switch and divided into two lines leading to the corresponding keys for different groups of lamps.
Useful LED Strip Information
This is an exceptionally convenient option for LED lighting, relatively inexpensive and easy to install. LED tapes, also called LED tapes, are polymer strips on which miniature LEDs with resistors are installed. The back side of the strip is usually provided with an adhesive layer.
LED tape is a flexible plastic strip, on one side of which LEDs are installed, and on the other, an adhesive base
Installing such a tape is very simple: you need to glue the element in a suitable place and connect it to the power supply. The LED strip is divided into equal segments, each of which contains a certain number of LEDs connected in series with each other.
Places for a cut of this design have special designations. In bathrooms, only moisture-proof Led tapes marked IP44 can be used. Such elements vary in power. There is a purely decorative option, and strong LEDs that give a large amount of light.
Separate segments of LED tape are connected using special moisture-proof connectors, cuts can be performed strictly according to the markings applied by the manufacturer
There are single and multi-color LED ribbons. The latter have a slightly more complex device: in addition to the general output, there are three more - one for each color.
When choosing an LED strip, one should take into account such an indicator as the density of LEDs, i.e. their number per meter. In addition, the adhesive layer is not always needed, there are designs without it.
The soldering of single-color segments of the tape is soldered according to the “plus or minus” principle. When installing a multi-color tape, the areas indicated by the indices V +, G, R, B are connected. To correctly select the power supply and controller, you need to calculate the length of the tape and multiply this figure by the power of one meter.
Installation of LED strip is simple. To do this, fix the tape and connect it to the power supply, controller and electrical network (+)
If the length of the structure exceeds 15 m, you will need to use another power supply, if the length is more than 30 m - two power supplies, etc. Connecting a mains wire is usually done to the pins, which are designated as N and L. For a multi-color ribbon, first install the controller.
If you need to bend the tape yourself when installing the LED lighting for the bath with your own hands, remember that the permissible bending diameter is 20 mm.
This type of backlight can be connected not only to a conventional switch, but also to a dimmer for an LED strip. This device allows you to adjust the brightness of the LEDs. A convenient option for controlling the backlight can be a portable remote control.
When working with LED strip, you must strictly observe the polarity, protect the structure from mechanical damage, adhere to the rules of fire and electrical safety. If you plan to fix the tape on a metal base, you should first cover it with insulating material.
LED strip leaves wide scope for various effects when decorating the interior.
In addition to highlighting the mirror, you can use it:
- to decorate the ceiling around the perimeter;
- to effectively highlight small shelves;
- for registration of a mirror;
- to visually highlight the bath;
- for arranging a fake window, etc.
If you install the LEDs under the bath, you can achieve the effect of soaring design. A fake window illuminated by LED strip can become a stylish decoration of the interior and visually expand a small space. An interesting addition are the luminous nozzles for the tap and shower.
If you lay the LED strip down the perimeter of the bath, you can achieve the effect of its soaring. Similarly, you can arrange other furnishings
Such elements are quite simple to install, they do not need to be connected to the mains. Of course, you should use these methods sparingly so as not to spoil the appearance of the bathroom with unnecessary details. With an excessive number of elements, the backlight will simply merge into one obscure light spot.
Mounting mirror lights
If LED auxiliary lighting is planned in the bathroom, then it is impossible to ignore the mirror. Lamps located around this element will not only decorate the interior, but will also make its use more convenient. For LED mirror illumination, a tape is usually used, single or multicolor, of suitable length.
Mirror illumination can be performed both with the help of spot LEDs and using LED-tape, as well as by combining these methods
If the mirror is large and the length of the tape exceeds five meters, you will have to stock up with connectors to connect individual segments of the tape. The design is connected via a power supply with a power that should be at least one and a half times greater than the power consumption of the used LED strip.
Of course, in the bathroom should only use waterproof LED strip. If it is necessary to cut it, then you need to do this, focusing on special tags made by the manufacturer, otherwise it can simply be ruined.Connect individual segments with connectors.
The tape can be glued directly on the surface of the mirror or on the wall behind it, it all depends on what design effect is planned to be obtained. But in any case, before gluing the LEDs, the surface should be degreased. After that, the tape is simply connected to the power supply.
The series connection of LED lights is described here:
This video shows the parallel connection of LEDs:
Here, the installation procedure for spotlights is shown in detail:
LEDs are a convenient and cost-effective option for organizing the main and auxiliary lighting in the bathroom. If you deal with all the requirements and instructions, the installation of such elements can be done independently.
Do you have personal experience in designing and arranging lighting in the bathroom? Want to share your knowledge or ask questions about the topic? Please leave comments and participate in discussions - the feedback form is located below.