Sitting near a private house or summer house in the summer heat, you probably imagined how cool it would be to plunge into the cool water of your own pool. Probably, you immediately drove away the thought of its device, but it persistently returned and literally pursued on hot days. Maybe you should not give up such an excellent idea?
After all, you can build a simple pool with your own hands, investing a minimum of money in the construction. And in this we are pleased to provide you with effective assistance by providing complete information support. Here you will learn about the varieties of artificial ponds and the features of choosing a place for the location of the bowl.
We have collected for you popular design options and technologies for their construction. A detailed description is supplemented by explanatory diagrams, step-by-step photo instructions and videos.
Planning and design selection
You should start, of course, with the project. First you need to assess the condition of the site, determine the place where the pool will be located, select the dimensions of the tank, the configuration of the bowl, etc.
An important point is the level of occurrence of the first groundwater horizon on the site. If this indicator is less than one meter, i.e. groundwater runs high, it is not recommended to build a stationary pool in the pit.
Image Gallery
Photo from
Option to build a pool in the country
Easy-to-mount frame structure
Paved inflatable pool
Assembling a pool of plastic modules
Hard frame device on the surface
Concrete pool construction
Special effects of a stationary pool
Alternatively, consider installing a portable frame or inflatable model.
Choosing a place to build your own pool, you should consider the following recommendations of specialists:
- The pool should be at a sufficient distance from the apartment building and other buildings, since the close proximity of these structures can destructively affect the integrity of the foundation of the building.
- It is undesirable to place a pool in the immediate vicinity of trees or plant them later, so that the root system, attracted by a large amount of moisture, does not grow and does not destroy the frame of the structure.
- The presence of a large number of trees near the pool also increases the intensity of its pollution by extraneous debris and stimulates the growth of algae.
- Clay soils are best suited for the construction of the pool, which serve as an additional barrier to ground moisture, if there is a choice, such a site should be reserved for the pool.
- Digging a large pit manually - an extremely laborious task, it is better to choose a place where construction equipment can be brought to: excavator, concrete mixer, possibly a crane, etc.
When the place is chosen, you need to take a sheet of paper and draw a future structure on it. You should choose the configuration of the bowl and its depth, as well as indicate the location of all communications: the place of water supply, the ladder for the descent, the installation location of the filter, overflow, backlight, external lighting, etc.
At the planning stage, it is necessary to consider the type of pumping and purification of water. The diagram shows a skimmer-type pool. Contaminated water is pumped out from the surface with a skimmer, and after cleaning with heating it is supplied through nozzles located opposite (+)
In addition to the main drainage area, it is recommended that an emergency water discharge system be provided. Electric wires must be laid in the corrugation.
At this stage, it is necessary to take into account the predominant direction of the wind in the area. Garbage that has fallen on the surface of the water will be blown away by the wind to a specific side of the pool.
An overflow variety of artificial reservoirs involves the outflow of contaminated water through an overflow trench into the container of the same name. After cleaning and heating it is supplied again to the pool through nozzles located in the bottom area.
In construction stores you can find sets of equipment for pools, including everything you need for installation.
Such a set may include:
- waterproofing materials;
- materials for the erection of the walls of the pool bowl;
- fittings;
- flanges and nozzles;
- filter, pump, skimmer;
- stairs;
- PVC film for decoration, etc.
The basic set can be supplemented with other elements, depending on the features of the design of the future pool.
The easiest way to install the pool for the summer season is to purchase a prefabricated version with the fixtures and equipment included in the package
When choosing the size of the structure, it should be remembered that for one adult, a depth of 1.5 m is considered suitable for swimming, and the recommended pool length is about 5 m. If you plan to install a diving board or a tower, you should build a 2.5 m deep pool or more.
The deeper the pool, the larger the volume of its bowl, the thicker the walls of the pool should be made, respectively, the more materials will be needed to perform the work.
Separately, it is worth discussing the configuration of the future pool. The following principle should be remembered here: the more complicated the outline of the bowl, the more efforts will be required to implement the project and the subsequent maintenance of the pool.
The easiest way to build a pool with rectangular, round or oval outlines of the bowl. If all these points have been taken into account in advance and the project has been drawn up correctly, much less problems will arise during construction.
For example, if there is no clear design, after pouring the bowl, concrete has to be additionally drilled to make holes for communications.
When choosing a pool of the wrong configuration, it should be borne in mind that the difficulties in its installation, as well as maintenance, can significantly increase
Installation of a concrete pool
Since working with concrete mix is familiar to most builders, a pool cast from this material is considered the most affordable option for self-production. But you can’t call it simple and easy.
Excavation pit and sand and gravel pillow
As mentioned earlier, it is best to use an excavator to dig a pit. If this is not possible, for example, there are no access roads for such bulky special equipment, you can perform these works manually, although this will require significantly more time.
So that the walls of the pit do not crumble during excavation, they should be given a slight bias. The bottom should have a slope towards the drain
So that the walls of the pit do not crumble, in the process of excavation they are given a slight bias. In the center of the bottom of the bowl make an additional recess for the device of a separate drainage well. The bottom of the pit should also have a slight slope (5-7%), directed to the place of water flow.
Backfill begins with a drainage well. It is simply filled with crushed stone and rammed flush with the surface of the bottom of the pit. After that, the bottom is covered with a layer of sand and gravel. At the same stage, one should consider the features of the installation of drain structures, etc.
First, a layer of sand with a thickness of about 20-30 cm is laid at the bottom, which is carefully and uniformly compacted. Then put a 10-centimeter pillow of gravel on top, which should also be tamped.
Regardless of the shape of the bowl and the material from which it is made, the pit is constructed in a certain sequence. First, choose the soil, then lay the communications, strengthen the bottom and walls, in the end install the bowl (+)
Concreting the bottom of the pool
After installing the communications, you can begin to fill the bottom with concrete.
The mixture can be prepared independently according to the following recipe:
- 625 kg of sand;
- 325 kg of cement;
- 1250 kg of crushed stone;
- 170 liters of water.
Since a lot of concrete is needed, it makes sense to buy, rent or even make a concrete mixer with your own hands. To calculate the required amount of the mixture and its components, you can use the online calculator. Such services are on many sites of suppliers of cement and building materials.
It also makes sense to consider the possibility of acquiring ready-mixed concrete for industrial production, especially if special equipment can be adjusted directly to the construction site. In the recommendations on how to make a pool of concrete with your own hands, there are two options for concreting the bottom of the pit.
In the first case, a layer of concrete screed 5 cm thick is first poured. Then, a reinforcement layer is mounted on top, which is poured with another layer of screed.
Some masters recommend reducing time and effort using the second fill option. In this case, the reinforcement is first mounted, which is installed at a certain distance from the sand and gravel cushion using supports (pieces of brick will do).
Before pouring the bottom of the foundation pit for the pool with a concrete screed, reinforcement made of metal rods 6-8 mm thick is laid on it.
Then the concrete mortar is poured onto the bottom so that it covers the bottom of the pit and all the reinforcement. For the preparation of concrete mortar, it is recommended to use cement grade M 400 or higher. Reinforcing mesh can be made of 6-8 mm metal wire.
The recommended cell size is 150-200 mm. The rods can be welded, but it will be easier to simply fix their position with a thin wire. Now you need to wait for the concrete screed to dry. From time to time, the surface of the concrete is wetted with water to achieve uniform drying.
Formwork and wall filling
Now you need to make the formwork to make the walls of the pool bowl of concrete. For this you need a 30 mm board. Immediately make sure that mounting holes are provided in which the pool equipment will be installed.
To improve the adhesion of the fresh mortar to the already laid concrete base, the base must be moistened before starting work. For the same purpose, aluminum powder is added to the solution for the first layer of wall filling.
Formwork for pouring the walls of a concrete pool can be made of boards or plywood. To increase the strength of the structure, it is strengthened with a beam
It is not necessary to use new boards for formwork, even old used structures will do, for example, with traces of old paint, etc. The main thing is that they support the weight of concrete. Moisture-resistant plywood is also suitable for these purposes. It is bent, so it is more convenient than a board when creating a formwork of a non-standard configuration.
The formwork should be further strengthened with stiffeners. They are made of timber 50X50 mm. The ribs are set approximately 500 mm apart. If the stationary staircase is to be made of concrete, then the crate for it must be done separately.
Reinforcement is also done in advance, which is needed to give additional strength to the concrete walls of the pool. Metal rods are installed immediately after the first layer has been poured, until the concrete has time to harden.
After this, concrete is poured in layers, each thickness is about 150 mm. After about four days, the concrete will become hard enough so that the formwork can be removed.
Waterproofing and finishing
After the concrete has completely dried, work can continue. First perform waterproofing work. Some masters consider it necessary to isolate only the so-called cold seams, while others advise laying a layer of waterproofing over the entire surface of the pool bowl.
Roofing material is quite suitable for the role of waterproofing, the sheets of which are laid with an overlap of about 200 mm. You can also use liquid rubber, bitumen, a PVC membrane or modern building mixtures with hydrophobic properties. It is important to consider the costs, since the area of the pool bowl is usually large, and such construction mixtures are quite expensive.
Liquid waterproofing is applied to the surface of the bowl of the concrete pool in two layers, between which it is necessary to install a reinforcing mesh
To improve the quality of waterproofing, you must first align the walls by grinding. If liquid waterproofing is used, which is sprayed onto the walls, two layers must be applied. In this case, it is recommended to lay a reinforcing mesh between the first and second layer.
After the waterproofing has dried, it is necessary to check its quality. To do this, the pool is filled with water and left for 10-12 days. Measure the water level at the beginning and end of this period. A slight difference between these indicators is quite expected, since water from the surface evaporates.
But if the water decreases too fast, it means that the waterproofing is not done correctly, the work should be repeated. After that, the surface of the pool can be plastered with a suitable composition to prepare the base for further finishing. A decorative border is made on the top of the pool. It can be cast from concrete or laid out of brick.
It remains to install the remaining equipment, and then to cover the pool walls with decorative material. Most often, ceramic tiles are used for this. Due to the pressure of the water layer, the walls of the bowl may be slightly deformed. This does not reflect well on the state of the tile: it cracks or crumbles.
To prevent such an unpleasant phenomenon, you need to make a wide seam between the tiles, and use a composition with increased elasticity for grouting. It is quite difficult to lay tiles on uneven surfaces. It is better for owners of pools with complex configurations not to use tiles, but mosaics.
At the end of the finishing work, you need to wait a little more time for the glue to dry well. After that, you can fill the pool with water to check the quality of its manufacture and the operation of the equipment.
Instead of coating and penetrating options for providing waterproofing of the pool walls, a polymer membrane can be used. It is recommended to lay in two layers, the seams of the material are welded with hot air (+)
The construction of the pool with a bowl on the surface
The organization option at the pool cottage, which is quite acceptable at the price and cost of construction, is to erect a frame from a board with a waterproofing sheath inside.
Stage # 1 - base and frame
To install a structure located completely on the day surface, you need to build a rigid, even base, able to withstand the weight of the water and bathing people collected in the bowl, and build a frame:
Image Gallery
Photo from
Step 1: Arrangement of the base and installation of supports
Step 2: Laying the waterproofing on the base
Step 3: Assembling the frame from the tongue and groove board
Step 4: Duplicating with a notch with a self-tapping screw
Step 5: building the walls of the pool
Step 6: Building Walls from a Thick Board
Step 7: Rules for joining the tongue and groove board
Step 8: Screwing screws into nodal connections
Stage # 2 - frame waterproofing
After the construction of the frame, it should be equipped for connecting communications, pumping and control equipment, prepared for laying the internal waterproofing coating and for installing additional devices.
Image Gallery
Photo from
Step 9: Forming holes for the filter and skimmer
Step 10: Verify Horizontalness After Cutting Holes
Step 11: Preparing the inner surface for waterproofing
Step 12: Flooring the waterproofing coating in the frame
Step 13: Fixing the waterproofing edge for leveling
Step 14: Adjusting the Waterproofing to Real Sizes
Step 15: Fixing Aligned Waterproofing
Step 16: Installing the final bar around the perimeter of the pool
Stage # 3 - connecting communications
A swimming pool is a hydraulic engineering structure, for the normal operation of which and to provide bathing conditions, a number of technical systems are required: pump, filter group, etc.
The technique requires weather protection, which will be performed by boxing, confined to the narrow wall of the bowl.
Image Gallery
Photo from
Step 17: Vertical Guide
Step 18: Installing the Horizontal Bar
Step 19: Assembling the walls of the room
Step 20: Installing Beams for the Box Roof Device
Step 21: Preparing the pool equipment for connection
Step 22: Rules for the arrangement of premises for equipment
Step 23: Using a Pressure Gauge to Monitor Pressure
Step 24: Boxing roof to protect equipment from rain and dust
Stage # 4 - arrangement of important details
At the end, the pool built on the summer cottage is equipped for ease of operation and maintenance.
Image Gallery
Photo from
Step 25: hanging the door leaf
Step 26: Lock for the room with appliances
Step 27: Assembling and installing a ladder
Step 28: Handrail over the box
Step 29: stainless steel staircase to the pool
Step 30: Awning for an open bowl of the country pool
Step 31: Rules for Using the Canvas Awning
Step 32: Reinforcing the Pool Frame
Alternative bowl erection options
When figuring out how to build a concrete pool, do not forget about alternative options for erecting a bowl.
For its construction, you can use:
- concrete blocks;
- polystyrene blocks;
- steel sheet;
- finished construction made of fiberglass or plastic.
When using concrete blocks, the bottom of the pool is first poured, but the walls of the bowl are laid out from these same blocks. Every third row of masonry should be reinforced to give the structure additional strength. Of the blocks, you can make a stationary staircase, instead of a stepladder, which is not so convenient.
The walls of the pool can be laid out of concrete blocks. Every third row of masonry should be reinforced. The surface of the bowl must be waterproofed, and then finishing work
Further, the bowl is processed in the same way as the monolithic design: waterproofing and finishing work are being carried out. As a decorative coating, you can use a special PVC film.
It looks very attractive, it is much cheaper than ceramic tile, and laying it is much easier. But the life of this material is only 5-7 years, then the finish will have to be updated.
PVC film is a convenient material for decorating pools. It is easy to install and looks attractive, but it only lasts a few years.
Large-format polystyrene blocks are also laid on a concrete base. They are connected using the design of the grooves and ridges.
The material is very convenient to use because it weighs a little. If necessary, the blocks are cut with a conventional hacksaw.
A pool with walls made of polystyrene foam blocks is not difficult to make. The structure should be reinforced, and then pour concrete mortar into special holes
After the masonry is completed, install the pool equipment, as well as the fittings. It is placed inside the cavities in the blocks.
The space between the communication pipes and polystyrene foam is blown with foam. After that, liquid concrete is pumped into the cavity with the reinforcement. When the structure has dried, you can begin to finish the finished bowl.
A steel sheet pool can be made both on a concrete base and on carefully compacted soil, although the latter option is not as reliable as a screed. Since the steel sheet is supplied in a roll, it is most convenient to make a bowl from it in the form of a circle, oval or “figure eight”.
A steel sheet basin can be round or oval. Such structures may be deepened or located on the surface.
The edges of the sheet are connected with a special profile, which eliminates welding work. After installing the bowl, it is covered with PVC film and filled with water so that the finishing material is pressed tightly against the walls of the bowl. To fix the film on top of the side using a mounting profile. After that, the technical equipment of the pool is installed.
A finished bowl made of fiberglass, plastic or modern composite materials is an expensive pleasure, even if you choose a standard design, rather than custom-made.
For delivery and installation of the bowl will have to use a crane and other special equipment. First dig a pit of a suitable configuration. Then its bottom is leveled, covered with a layer of gravel or gravel and rammed.
It is not easy to deliver the finished bowl for the pool and install it in the pit, but its further installation is relatively simple, since waterproofing and decoration are not needed
After that, you can lower the bowl to the bottom of the pit. The space between the walls of the pit and the bowl is covered with soil and rammed. Such structures usually do not need additional waterproofing and finishing. It remains to install equipment and start operating the pool.
The weight of such pools is usually relatively low, so caution should be exercised to owners of areas with high levels of freezing. In winter, frozen groundwater can simply push the bowl to the surface.
Useful can be seen on the topic
Here, the experience of pouring the bowl of a small rectangular pool of concrete was clearly demonstrated:
This video details the process of finishing the pool with PVC film:
Arranging your own pool on the site can be performed even by a novice master. To do this, you need to properly design the structure, and then perform all the necessary work, strictly observing the technology. With proper care, a home-made pool will serve for many years.
Do you want to get your own pool, but have not decided which is better to choose? Maybe there is already experience in the construction, or is there something to recommend to us and visitors to the site? Please write comments in the block below, express an opinion, ask questions, post a photo on the topic of the article.